Exactly How to Remove and Change a Bathtub.
Exactly How to Remove and Change a Bathtub.
Blog Article
Have you been trying to find related information on How to Install a Bathtub?
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bathtub with a new one is additionally a moderately tough task. If the old tub is easily accessible, the job can relocate quickly; if you have to open up a wall surface to get rid of the old tub and place the brand-new bathtub, the task is much harder. In either instance, the task is within a home handyman's skills, although you will require an assistant to vacate the old bathtub and set in the new one. Make certain you have actually certified on your own for the job and are comfortable trying it. As opposed to working with a contractor to take control of a halfway-completed project, it is better to take into consideration utilizing one prior to you start. Chances are you might require a professional plumber to make tube connections.
This short article will certainly assist you mount a brand-new bath tub in your bathroom if you have already purchased a new tub and don't need to change the arrangement of your previous supply of water pipes.
Your tools and material list should consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you must do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic due to the restricted gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will come from the pipes. As soon as the supply pipelines have been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
Before going on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making sure that the washers remain in place between the faucet and the sink. Safeguard the tap in position with the producer given backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The previous type must be connected to the faucet ends first, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Tub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in evenly spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 small factors.
The following goal is to make sure that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out degree.
To set up faucets, fit all-time low of the furthest flexible tap port to the ideal supply pipe by making a compression sign up with; after that do the very same for the other tap.
Activate the water supply and inspect all joints as well as brand-new pipework for leakages and also tighten them if essential. Fill the bathtub and likewise examine the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as securing around the tub needs to wait till the bath tub has actually been used at least when as this will certainly resolve it right into its last position.
Preparing for the Installation
Firstly, the supporting framework supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath must now prepare to be fitted in its final setting.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bath and also the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes and also cartridges, as well as can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the bath tub with water before securing, to allow for the motion experienced when the tub is in use. The sealer can crack relatively early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly readily available on the market. It is suggested to fit the tiles utilizing waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that article on Installing A Bathtub while doing a search on the internet. Sharing is good. Who knows, you may very well be helping someone out. Thank you so much for going through it.
Click Here To Find Out More Report this page